Johnson–Nyquist noise

From Wikipedia, the free encyclopedia
These three circuits are all equivalent: (A) A resistor at nonzero temperature, which has Johnson noise; (B) A noiseless resistor in series with a noise-creating voltage source (i.e. the Thévenin equivalent circuit); (C) A noiseless resistance in parallel with a noise-creating current source (i.e. the Norton equivalent circuit).

Johnson–Nyquist noise (thermal noise, Johnson noise, or Nyquist noise) is the electronic noise generated by the thermal agitation of the charge carriers (usually the electrons) inside an electrical conductor at equilibrium, which happens regardless of any applied voltage. Thermal noise is present in all electrical circuits, and in sensitive electronic equipment (such as radio receivers) can drown out weak signals, and can be the limiting factor on sensitivity of electrical measuring instruments. Thermal noise increases with temperature. Some sensitive electronic equipment such as radio telescope receivers are cooled to cryogenic temperatures to reduce thermal noise in their circuits. The generic, statistical physical derivation of this noise is called the fluctuation-dissipation theorem, where generalized impedance or generalized susceptibility is used to characterize the medium.

Thermal noise in an ideal resistor is approximately white, meaning that the power spectral density is nearly constant throughout the frequency spectrum, but does decay to zero at extremely high frequencies (terahertz for room temperature). When limited to a finite bandwidth, thermal noise has a nearly Gaussian amplitude distribution.[1]

History of thermal noise[edit]

In 1905, in one of Albert Einstein's Annus mirabilis papers the theory of Brownian motion was first solved in terms of thermal fluctuations. The following year, in a second paper about Brownian motion, Einstein suggested that the same phenomena could be applied to derive thermally-agitated currents, but did not carry out the calculation as he considered it to be untestable.[2]

Geertruida de Haas-Lorentz, daughter of Hendrik Lorentz, in her doctoral thesis of 1912, expanded on Einstein stochastic theory and first applied it to the study of electrons. Deriving a formula for the mean-squared value of the thermal current.[2][3]

Walter H. Schottky studied the problem in 1918, while studying thermal noise using Einstein's theories, experimentally discovered another kind of noise, the shot noise.[2]

Frits Zernike working in electrical metrology, found unusual aleatory deflections while working with high-sensitive galvanometers. He rejected the idea that the noise was mechanical, and concluded that it was of thermal nature. In 1927, he introduced the idea of autocorrelations to electrical measurements and calculated the time detection limit. His work coincided with de Haas-Lorentz' prediction.[2]

The same year, working independently without any knowledge of Zernike's work, John B. Johnson working in Bell Labs found the same kind of noise in communication systems, but described it in terms of frequencies.[4][5][2] He described his findings to Harry Nyquist, also at Bell Labs, who was able to explain the results, published in 1928.[6]

Derivation[edit]

As Nyquist stated in his 1928 paper, the sum of the energy in the normal modes of electrical oscillation would determine the amplitude of the noise. Nyquist used the equipartition law of Boltzmann and Maxwell. Using the concept potential energy and harmonic oscillators of the equipartition law,[7]

where is the noise power density in (W/Hz), is the Boltzmann constant and is the temperature. Multiplying the equation by bandwidth gives the result as noise power.

where N is the noise power and Δf is the bandwidth.

Noise voltage and power[edit]

Thermal noise is distinct from shot noise, which consists of additional current fluctuations that occur when a voltage is applied and a macroscopic current starts to flow. For the general case, the above definition applies to charge carriers in any type of conducting medium (e.g. ions in an electrolyte), not just resistors. It can be modeled by a voltage source representing the noise of the non-ideal resistor in series with an ideal noise free resistor.

The one-sided power spectral density, or voltage variance (mean square) per hertz of bandwidth, is given by

where kB is Boltzmann's constant in joules per kelvin, T is the resistor's absolute temperature in kelvins, and R is the resistor value in ohms (Ω). Using this equation for quick calculation, at room temperature:

For example, a 1 kΩ resistor at a temperature of 300 K has

For a given bandwidth, the root mean square (RMS) of the voltage, , is given by

where Δf is the bandwidth in hertz over which the noise is measured. For a 1 kΩ resistor at room temperature and a 10 kHz bandwidth, the RMS noise voltage is 400 nV.[8] A useful rule of thumb to remember is that 50 Ω at 1 Hz bandwidth correspond to 1 nV noise at room temperature.

A resistor in a short circuit dissipates a noise power of

The noise generated at the resistor can transfer to the remaining circuit; the maximum noise power transfer happens with impedance matching when the Thévenin equivalent resistance of the remaining circuit is equal to the noise-generating resistance. In this case each one of the two participating resistors dissipates noise in both itself and in the other resistor. Since only half of the source voltage drops across any one of these resistors, the resulting noise power is given by

where P is the thermal noise power in watts. Notice that this is independent of the noise-generating resistance.

Noise current[edit]

The noise source can also be modeled by a current source in parallel with the resistor. Taking the Norton equivalent of the voltage source corresponds to dividing the noise voltage by R. This gives the root mean square value of the current source as:

Noise power in decibels[edit]

Signal power is often measured in dBm (decibels relative to 1 milliwatt). From the equation above, noise power in a resistor at room temperature, in dBm, is then:

At room temperature (300 K) this is approximately

[9][10]: 260 

Using this equation, noise power for different bandwidths is simple to calculate:

Bandwidth Thermal noise power
at 300 K (dBm)
Notes
1 Hz −174
10 Hz −164
100 Hz −154
1 kHz −144
10 kHz −134 FM channel of 2-way radio
100 kHz −124
180 kHz −121.45 One LTE resource block
200 kHz −121 GSM channel
1 MHz −114 Bluetooth channel
2 MHz −111 Commercial GPS channel
3.84 MHz −108 UMTS channel
6 MHz −106 Analog television channel
20 MHz −101 WLAN 802.11 channel
40 MHz −98 WLAN 802.11n 40 MHz channel
80 MHz −95 WLAN 802.11ac 80 MHz channel
160 MHz −92 WLAN 802.11ac 160 MHz channel
1 GHz −84 UWB channel

Thermal noise on capacitors[edit]

Ideal capacitors, as lossless devices, do not have thermal noise, but as commonly used with resistors in an RC circuit, the combination has what is called kTC noise. The noise bandwidth of an RC circuit is Δf = 1/(4RC).[11] When this is substituted into the thermal noise equation, the result has an unusually simple form as the value of the resistance (R) drops out of the equation. This is because higher R decreases the bandwidth as much as it increases the noise.

The mean-square and RMS noise voltage generated in such a filter are:[12]

The noise charge is the capacitance times the voltage:

This charge noise is the origin of the term "kTC noise".

Although independent of the resistor's value, 100% of the kTC noise arises in the resistor. Therefore, if the resistor and the capacitor are at different temperatures, the temperature of the resistor alone should be used in the above calculation.

An extreme case is the zero bandwidth limit called the reset noise left on a capacitor by opening an ideal switch. The resistance is infinite, yet the formula still applies; however, now the RMS must be interpreted not as a time average, but as an average over many such reset events, since the voltage is constant when the bandwidth is zero. In this sense, the Johnson noise of an RC circuit can be seen to be inherent, an effect of the thermodynamic distribution of the number of electrons on the capacitor, even without the involvement of a resistor.

The noise is not caused by the capacitor itself, but by the thermodynamic fluctuations of the amount of charge on the capacitor. Once the capacitor is disconnected from a conducting circuit, the thermodynamic fluctuation is frozen at a random value with standard deviation as given above. The reset noise of capacitive sensors is often a limiting noise source, for example in image sensors.

Any system in thermal equilibrium has state variables with a mean energy of kT/2 per degree of freedom. Using the formula for energy on a capacitor (E = ½CV2), mean noise energy on a capacitor can be seen to also be ½C(kT/C) = kT/2. Thermal noise on a capacitor can be derived from this relationship, without consideration of resistance.

Noise of capacitors at 300 K
Capacitance Electrons
1 fF 2 mV 2 aC 12.5 e
10 fF 640 µV 6.4 aC 40 e
100 fF 200 µV 20 aC 125 e
1 pF 64 µV 64 aC 400 e
10 pF 20 µV 200 aC 1250 e
100 pF 6.4 µV 640 aC 4000 e
1 nF 2 µV 2 fC 12500 e

Generalized forms[edit]

The voltage noise described above is a special case for a purely resistive component for low frequencies. In general, the thermal electrical noise continues to be related to resistive response in many more generalized electrical cases, as a consequence of the fluctuation-dissipation theorem. Below a variety of generalizations are noted. All of these generalizations share a common limitation, that they only apply in cases where the electrical component under consideration is purely passive and linear.

Reactive impedances[edit]

Nyquist's original paper also provided the generalized noise for components having partly reactive response, e.g., sources that contain capacitors or inductors.[6] Such a component can be described by a frequency-dependent complex electrical impedance . The formula for the power spectral density of the series noise voltage is

The function is simply equal to 1 except at very high frequencies, or near absolute zero (see below).

The real part of impedance, , is in general frequency dependent and so the Johnson–Nyquist noise is not white noise. The rms noise voltage over a span of frequencies to can be found by integration of the power spectral density:

.

Alternatively, a parallel noise current can be used to describe Johnson noise, its power spectral density being

where is the electrical admittance; note that

Quantum effects at high frequencies or low temperatures[edit]

Nyquist also pointed out that quantum effects occur for very high frequencies or very low temperatures near absolute zero.[6] The function is in general given by[13]

where is Planck's constant and is a multiplying factor.

At very high frequencies , the function starts to exponentially decrease to zero. At room temperature this transition occurs in the terahertz, far beyond the capabilities of conventional electronics, and so it is valid to set for conventional electronics work.

Relation to Planck's law[edit]

Nyquist's formula is essentially the same as that derived by Planck in 1901 for electromagnetic radiation of a blackbody in one dimension—i.e., it is the one-dimensional version of Planck's law of blackbody radiation.[14] In other words, a hot resistor will create electromagnetic waves on a transmission line just as a hot object will create electromagnetic waves in free space.

In 1946, Robert H. Dicke elaborated on the relationship,[15] and further connected it to properties of antennas, particularly the fact that the average antenna aperture over all different directions cannot be larger than , where λ is wavelength. This comes from the different frequency dependence of 3D versus 1D Planck's law.

Multiport electrical networks[edit]

Richard Q. Twiss extended Nyquist's formulas to multi-port passive electrical networks, including non-reciprocal devices such as circulators and isolators.[16] Thermal noise appears at every port, and can be described as random series voltage sources in series with each port. The random voltages at different ports may be correlated, and their amplitudes and correlations are fully described by a set of cross-spectral density functions relating the different noise voltages,

where the are the elements of the impedance matrix . Again, an alternative description of the noise is instead in terms of parallel current sources applied at each port. Their cross-spectral density is given by

where is the admittance matrix.

Continuous electrodynamic media[edit]

The full generalization of Nyquist noise is found in fluctuation electrodynamics, which describes the noise current density inside continuous media with dissipative response in a continuous response function such as dielectric permittivity or magnetic permeability. The equations of fluctuation electrodynamics provide a common framework for describing both Johnson–Nyquist noise and free-space blackbody radiation.[17]

See also[edit]

References[edit]

  1. ^ John R. Barry; Edward A. Lee; David G. Messerschmitt (2004). Digital Communications. Sprinter. p. 69. ISBN 9780792375487.
  2. ^ a b c d e Dörfel, G. (2012-08-15). "The early history of thermal noise: The long way to paradigm change". Annalen der Physik. 524 (8): 117–121. doi:10.1002/andp.201200736. ISSN 0003-3804.
  3. ^ Van Der Ziel, A. (1980-01-01), Marton, L.; Marton, C. (eds.), "History of Noise Research", Advances in Electronics and Electron Physics, Academic Press, vol. 50, pp. 351–409, doi:10.1016/s0065-2539(08)61066-5, retrieved 2024-03-16
  4. ^ Anonymous (1927). "Minutes of the Philadelphia Meeting December 28, 29, 30, 1926". Physical Review. 29 (2): 350–373. Bibcode:1927PhRv...29..350.. doi:10.1103/PhysRev.29.350.
  5. ^ Johnson, J. (1928). "Thermal Agitation of Electricity in Conductors". Physical Review. 32 (97): 97–109. Bibcode:1928PhRv...32...97J. doi:10.1103/physrev.32.97.
  6. ^ a b c Nyquist, H. (1928). "Thermal Agitation of Electric Charge in Conductors". Physical Review. 32 (110): 110–113. Bibcode:1928PhRv...32..110N. doi:10.1103/physrev.32.110.
  7. ^ Tomasi, Wayne (1994). Electronic Communication. Prentice Hall PTR. ISBN 9780132200622.
  8. ^ Google Calculator result for 1 kΩ room temperature 10 kHz bandwidth
  9. ^ Pierce, J. R. (1956). "Physical Sources of Noise". Proceedings of the IRE. 44 (5): 601–608. doi:10.1109/JRPROC.1956.275123. S2CID 51667159.
  10. ^ Vizmuller, Peter (1995), RF Design Guide, Artech House, ISBN 0-89006-754-6
  11. ^ Lundberg, Kent H. "Noise Sources in Bulk CMOS" (PDF). p. 10.
  12. ^ Sarpeshkar, R.; Delbruck, T.; Mead, C. A. (November 1993). "White noise in MOS transistors and resistors" (PDF). IEEE Circuits and Devices Magazine. 9 (6): 23–29. doi:10.1109/101.261888. S2CID 11974773.
  13. ^ Callen, Herbert. "Irreversibility and Generalized Noise". Physical Review. 83 (1): 34.
  14. ^ Urick, V. J.; Williams, Keith J.; McKinney, Jason D. (2015-01-30). Fundamentals of Microwave Photonics. John Wiley & Sons. p. 63. ISBN 9781119029786.
  15. ^ Dicke, R. H. (1946-07-01). "The Measurement of Thermal Radiation at Microwave Frequencies". Review of Scientific Instruments. 17 (7): 268–275. Bibcode:1946RScI...17..268D. doi:10.1063/1.1770483. PMID 20991753. S2CID 26658623.
  16. ^ Twiss, R. Q. (1955). "Nyquist's and Thevenin's Theorems Generalized for Nonreciprocal Linear Networks". Journal of Applied Physics. 26 (5): 599–602. Bibcode:1955JAP....26..599T. doi:10.1063/1.1722048.
  17. ^ Pitaevskii, L. P.; Lifshitz, E. M. (1980). "Chapter VIII. Electromagnetic Fluctuations". Statistical Physics, Part 2: Theory of the Condensed State. Vol. 9 (1st ed.). Butterworth-Heinemann. ISBN 978-0-7506-2636-1.

Public Domain This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22. (in support of MIL-STD-188).

External links[edit]